| RTP200W厚膜無感電阻2Ω4Ω6Ω8Ω11Ω15Ω100Ω100KΩ |
 |
價格：10 元(人民幣) | 產地：深圳市 |
| 最少起訂量：1只 | 發貨地：本地至全國 | |
| 上架時間：2025-12-26 10:55:54 | 瀏覽量：291 | |
深圳市華鑫歐電子有限公司
 |
||
| 經營模式：生產加工 | 公司類型：私營有限責任公司 | |
| 所屬行業：電阻器、電位器 | 主要客戶：艾默生，中興通訊，TCL,華為技術，長城集團... | |
 在線咨詢  |
||
| 聯系人:吳偉 (先生) | 手機:13554875208 |
電話: |
傳真: |
| 郵箱:szhxwuwei2008@163.com | 地址:深圳市寶安區石巖鎮洲石路石頭山工業區2號廠房3樓 |
|
功率型 厚膜 無感 電阻器 Power type Thick film Non inductive Resistor
l 電阻器的高度在端子面極低，為 11.8mm，端子為銅板襯套可直接用 M4 螺釘安裝。
The height of the resistor is extremely low on the terminal surface, at 11.8mm, and the terminal is a copper plate bushing that can be directly installed with M4 screws. l SOT-227 標準封裝
SOT-227 standard packaging
l 可以用 2 個 M4 螺釘簡單地安裝。
It can be easily installed with 2 M4 screws.
l 阻值范圍寬、體積小、功率大、耐熱性好
Wide resistance range, small size, high power, good heat resistance
l 端子的數量標準為 4 個，可以變更為 2 個、3 個。
The standard quantity of terminals is 4, which can be changed to 2 or 3.
主要應用于變速驅動器、供電、 控制設備、通訊、自動控制、發動機控制等。適合逆變器電路、脈沖電路、高頻電路。
Mainly used in variable speed drives, power supply, control equipment, communication, automatic control, engine control, etc. Suitable for inverter circuits, pulse circuits, and high-frequency circuits.
©2025 V1.0
功率型 厚膜 無感 電阻器 Power type Thick film Non inductive Resistor
©2025 V1.0
功率型 厚膜 無感 電阻器 Power type Thick film Non inductive Resistor
l 左下角引出端為 1 號引出端，按順時針旋轉分別為 3 號、4 號、2 號引出端
The lead out terminal in the lower left corner is the first lead out terminal, which rotates clockwise to become the second, third, and fourth lead out terminals, respectively
©2025 V1.0
功率型 厚膜 無感 電阻器 Power type Thick film Non inductive Resistor l 電阻器通過 M4 螺絲安裝在散熱器上，螺絲安裝扭矩為 2N.m，應確保產品安裝緊固，無晃動。另外應為螺絲配套防松組件，如：平墊、彈墊、防松螺母等。
l The resistor is installed on the heat sink with M4 screws, and the installation torque of the screws is 2N. m. It should be ensured that the product is installed firmly without shaking. In addition, screws should be equipped with anti loosening components such as flat washers, spring washers, anti loosening nuts, etc.
l 電阻器引出端電氣安裝使用的是 M4 螺絲，螺絲安裝扭矩為 1.3N.m，應確保電氣連接緊固，無晃動。另外應為螺絲配套防松組件，如：平墊、彈墊等，防止振動造成電氣連接松脫。
l M4 screws are used for the electrical installation of the resistor lead out end, with a torque of 1.3N. m. It should be ensured that the electrical connection is tight and there is no shaking. In addition, screws should be equipped with anti loosening components, such as flat washers, spring washers, etc., to prevent electrical connections from loosening due to vibration.
l 電阻器與安裝面之間需要均勻的涂覆一層導熱硅脂，推薦使用導熱系數 1W/mK 的導熱硅脂產品。
l A uniform layer of thermal grease should be applied between the resistor and the installation surface. It is recommended to use thermal grease products with a thermal conductivity of 1W/mK.
l 產品在貯存期間，應貯存在環境溫度為-10℃～+45℃，相對濕度不大于 85% ，通風、干燥、周圍無酸堿或其他有害物質的倉庫內。
l During storage, the product should be stored in a warehouse with an ambient temperature of -10 ℃ to+45 ℃, a relative humidity of no more than 85%, ventilation, dryness, and no acidic, alkaline, or other harmful substances around it
|
| 版權聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責。機電之家對此不承擔任何責任。 友情提醒：為規避購買風險，建議您在購買相關產品前務必確認供應商資質及產品質量。 |
