亚洲综合在线播放_久久视频免费在线_久久久黄色av_亚洲免费视频一区

牛皮紙不干膠復合機 橋架式詳細介紹

江蘇鑫利龍智能機械有限公司主營產品熱熔膠油膠兩用復合機、pur熱熔膠復合機、不干膠復合機、砂紙復合機、撒粉復合機、水膠復合機、油膠復合機、火焰復合機、智能裁斷機、全自動裁斷機、液壓裁斷機等系列產品，***應用于地板、地毯、 拼圖、木業、吸塑、包裝、聚氨酯、日用家紡、鞋帽包袋、服裝玩具、體育用品(球類）、磨料磨具(砂紙)、醫療用品、空調冰箱密封件、汽車內飾件、印刷不干膠等行業，***國內。公司以***的質量，具有競爭力的 價格，完善的售后服務體系，力求使廣大客戶滿意，竭誠歡迎海內外客商，朋友指導工作，共創事業輝煌。

離型紙不干膠復合機

設備特點：
不干膠復合機采用水性或油性作粘合劑，經地高溫烘箱的烘干硫化，具有較強的粘合力，與其它材料貼合，即撕即用，方便快捷。
烘箱箱體都設有保溫層，加熱系統具有自動控溫性能，可以有效節約能源，降低生產成本。
客戶可以根據需要選配直流電機或變頻器聯動，從而使機器具有更好的操控性。

操作要求：

操作者只有在完全熟悉，掌握機器的性能，工作原理后方可操作本設備。本設備必須有專人操作，非操作人員不能亂開，亂動。

生產前應檢查電纜、斷路器、接觸器、電機等電器是否符合要求。

生產前須檢查三相電源是否均衡，嚴禁缺相啟動設備。

生產期應檢查各旋轉接頭是否安全，管路是否暢通，有無破損，漏油，并及時排除。

生產前須將熱油機打開，待溫度升至工藝要求溫度后，方可生產。生產前應檢查各氣壓表壓力是否正常，氣路有無漏氣，并及時修復.

設備大批量生產前，應先做小量試驗，成功后方可大批生產。

生產前，應檢查各液壓站、減速機、軸承瓦盒、絲杠等潤滑情況，應正確及時的加注液壓油和潤滑油。

停機后，必須及時清洗膠槽及刮膠附件，網紋輥，清除機器各部分殘膠及污垢，以備下次使用。

Operational requirements:

Operators can operate the equipment only after they are fully familiar with the performance and working principle of the machine. The equipment must be operated by a special person, and non-operator can not be disorderly opened and disturbed.

Before production, electrical appliances such as cables, circuit breakers, contactors and motors should be inspected to meet the requirements.

Before production, it is necessary to check whether the three-phase power supply is balanced or not, and startup equipment without phase is strictly prohibited.

During the production period, it should check whether the rotary joints are safe, whether the pipeline is smooth, whether there is any damage, oil leakage, and timely removal.

The hot oil engine must be turned on before production, and can be produced only after the temperature is raised to the required temperature of the process. Before production, check whether the pressure of each barometer is normal, whether there is air leakage in the air passage, and repair it in time.

Before large-scale production of equipment, small-scale test should be done before large-scale production can be achieved.

Before production, the lubrication conditions of hydraulic stations, reducers, bearing bushes, screw, etc. should be checked, and the hydraulic oil and lubricating oil should be injected correctly and timely.

After shutdown, the rubber trough and scraper accessories, mesh rollers must be cleaned in time to remove residual glue and dirt from all parts of the machine for next use.