亚洲综合在线播放_久久视频免费在线_久久久黄色av_亚洲免费视频一区

重慶市 重慶江北區  重慶渝北區  重慶沙坪壩區  重慶九龍坡區  重慶萬州區  重慶永川市  重慶南岸區  重慶酉陽縣  重慶北碚區  重慶涪陵區  重慶秀山縣  重慶巴南區  重慶渝中區 重慶 石柱縣  重慶忠縣  重慶合川市  重慶大渡口區  重慶開縣  重慶長壽區  重慶榮昌縣  重慶云陽縣  重慶梁平縣  重慶潼南縣  重慶江津市 重慶彭水縣  重慶璧山縣  重慶綦江縣  重慶大足縣  重慶黔江區  重慶巫溪縣  重慶巫山縣  重慶墊江縣  重慶豐都縣  重慶武隆縣  重慶萬盛區  重慶銅梁縣  重慶南川市  重慶奉節縣  重慶雙橋區  重慶城口縣

There are three parts supporting with the wire. 1. The pins. 2. The pin stands and 3. The teeth guide.
5.3.1導線塊是各種齒距通用一個規格，只須通過調整導線塊旁邊的“齒距調節螺絲”將其左右移動位置。Wire running teeth guide is a kind of common specification. Just loosen the screws can move it to left or right position.
5.3.2穿好線之后先用“手動繞線”生產一段線圈,檢驗齒距是否符合要求(可以在機器上的導向齒距條上檢驗),如齒距偏大,則把“齒距調節螺絲”順時針旋轉,反之亦反。Upon the wire setup done “manual wiring” trial suitable length of coil. In case double check each coil is qualified passed. (Can inspect onto the machine on the teeth pitch guide).If the teeth pitch bigger adjust screws turn clock wise. If teeth pitch smaller, turn against the direction.

5.4全自動臺歷 掛歷 筆記本單/雙線圈裝訂機調試切刀 Cutter adjustment

5.4.1 先調試左切刀,刀口的開口中間位置對準需切斷的線圈位置,刀口進入線圈約1/3,見下圖.用同樣的方法調試右切刀 。Adjust the left cutter; the centre of the cutter must face the wire cutting position. The cutter should be entered the coil 1/3 of depth. See photo 3. Use the same way for the right cutter for inspection.

5.4.2  切刀高度調整,在切刀架上有一個可調整的固定螺絲,松開調整到合適的位置鎖緊即可.見圖. Adjust the height for the cutter. There are adjustable screws, hoist it up can limited the cutter the height. See photo 4.

5.4.3 切刀左右位置調整，用板手松開切刀的固定滑塊即可將切刀左右移動,移動到所需要的位置后再將固定滑塊鎖緊. Adjust the left or right position for the cutter. Loosen screw rings can move the cutter to left or right position. Tighten up when the adjustment done.

5.5 全自動臺歷 掛歷 筆記本單/雙線圈裝訂機潤滑 Lubrications
線材須保持足夠的潤滑,否則表面容易刮花,請在機器放線架的潤滑盒子上加注乳化水. Wire material should be keep suitable lubrication to avoid scratch problem. Please put some Castrol Syntilo for lubrications.

6.全自動臺歷 掛歷 筆記本單/雙線圈裝訂機機器手送料系統的調整 Adjust the feed system

  The feed system of the machine is composed of the timing belt and the synchronous wheel. The position has been debugged in the right place in the factory. After a period of operation, if the tension of the belt is not enough or the position of the manipulator is deviated, the belt driven wheel can be adjusted Tighten the screws to ensure the tension of the timing belt, and then release the belt fastening block 1 to adjust the manipulator to the desired position to lock（Picture 6）。