亚洲综合在线播放_久久视频免费在线_久久久黄色av_亚洲免费视频一区

書刊裝訂設備的操作及更換零部件折卸方法 Testing and running 
1．安全操作注意事項 Notice of safety operate

1.2 了解機器各部分的作用和潛在危險區域，知道必要的安全措施。

Understand the role of the various parts of the machine and potentially dangerous areas, and know the necessary safety measures

1.3 啟動機器前，檢查機器各手柄，按鈕是否處于預定的工作位置。

Before starting the machine, check the handle of the machine and whether the button is in the intended working position. 

1.4 如果書刊裝訂設備作時突然停止，不要馬上重新啟動，應該按下“總停”自鎖按鈕，檢查停機原因，待故障排除后方可重新啟動。                 If the machine suddenly stops working, do not restart immediately, you should press the "total stop" self-locking button, check the cause of the shutdown, to be troubleshooting before you can restart. 
1.5 不允許在書刊裝訂設備運轉時，維護運動零部件和靠近運動零部件的其他零部件。 It is not permissible to maintain moving parts and other parts near moving parts while the machine is running.
1.6 大面積保養或修理時，必須按下“停止”自鎖按鈕，切斷所以電源、氣源。Large area maintenance or repair, you must press the "stop" self-locking button, cut off the power supply, gas source. 
1.7 書刊裝訂設備在進行調整、保養和修理工作時，不得使用不適當的工具。工作完畢后必須清理檢查機器上的工具和其他雜物，以免發生故障。 Undue tools should not be used for adjustment, maintenance and repair work. After the work must be cleaned to check the tools and other debris on the machine, so as to avoid failure.
1.8 在重新啟動機器前，應檢查所有安全設施是否處在正常位置，是否緊定，注意機器周圍的其他人員是否處在安全的位置。 Before restarting the machine, check that all safety devices are in their normal position, are they tightened, and that the rest of the machine is in a safe place.
1.9 保持書刊裝訂設備和周圍環境的清潔，及時清除掉落在地板上的油污，清理工作區的工具、抹布及碎紙廢料等。 Keep the machine and the surrounding environment clean, remove the oil on the floor in a timely manner, clean up the work area of the tools, rags and shredded scrap.
1.10 及時維護、更換已失效和損壞的裝置，及時報告機器發生的問題。Timely maintenance, replacement of failure and damage to the device, the timely report of the machine problems. 

書刊裝訂設備收放物料裝置的調整 Adjust the feed and receive belt
2.1 上料裝置的調整 Adjust the feed belt

  該工位可根據產品的寬窄來調節輸送料道的寬度，松開護罩1的固定螺絲123，然后根據產品的需要調整料道的寬窄。The position of the station can be adjusted according to the width of the product to adjust the width of the conveyor material, refer to (Picture 9) to release the cover screw 1 123, and then adjust the width of the material according to the needs of the material.

2.2書刊裝訂設備收料裝置的調整 Adjust the receive belt

  該工位主要是配合主機完成收料工作，可根據主機的裝訂速度自動調整線體的每次位移. The station is mainly with the host to complete the receipt work, according to the host's binding speed automatically adjust the line of each displacement.

3. 書刊裝訂設備推刀調試 Test push knife

   根據產品大小的需要，可通過調節推刀組的固定螺絲的安裝位置來調節T的寬度（見圖十）Depending on the size of the product, the width of the T can be adjusted by adjusting the mounting position of the setscrews' fixing screws (Picture 10)

4.書刊裝訂設備機器手送料系統的調整 Adjust the feed system

北京市  廣東省  山東省  江蘇省  河南省  上海市  河北省  浙江省  香港特別行政區  陜西省  湖南省  重慶市  福建省  天津市  云南省  四川省  廣西壯族自治區  安徽省  海南省  江西省  湖北省  山西省  遼寧省  臺灣省  黑龍江  內蒙古自治區  澳門特別行政區  貴州省  甘肅省  青海省  新疆維吾爾自治區  西藏區  吉林省  寧夏回族自治區