| SR塑性填料））面板止水材料集團公司！ |
 |
價格：0 元(人民幣) | 產地：衡水 |
| 最少起訂量：1米 | 發貨地：衡水 | |
| 上架時間：2017-11-21 14:36:23 | 瀏覽量：118 | |
衡水漢江橡塑科技有限公司
 |
||
| 經營模式：生產加工 | 公司類型：私營有限責任公司 | |
| 所屬行業：橡膠原料/橡膠制品 | 主要客戶：韓經理 | |
 在線咨詢  |
||
| 聯系人:段經理 (先生) | 手機:13091176335 |
電話: |
傳真: |
| 郵箱:1334576766@qq.com | 地址:河北 衡水市桃城區 彭杜村鄉 |
|
SR柔性填料性能特點：具有獨特性.高塑性、耐熱性、耐寒性、耐老化性，還具有操作簡便，無毒無味，耐水、粘附性能好等特點. SR flexible filler performance characteristics: unique, high plasticity, heat resistance, cold resistance, aging resistance, but also has the advantages of simple operation, non-toxic, tasteless, water resistance, good adhesion and other characteristics (1)施工準備用鋼筋臺車將“SR”填料、“SR”防滲蓋板、電鍍角鋼及電鍍膨脹螺栓等運至相應的施工部位rhxs。 (1) the steel trolley for construction preparation will transport the "SR" filler, "SR" impervious cover plate, electroplating angle steel and electroplating expansion bolt to the corresponding construction site rhxs. (2)嵌縫處理用鋼刷將預留“v”槽內兩側清理干凈，再用水沖洗槽內外，除去縫面上的灰砂。“V”槽清理干凈后自然晾干。 (2) the steel brush will be reserved for the "V" slot on both sides of clean caulking treatment, then rinse tank inside and outside, remove seam on the surface of the sand. The "V" groove is cleaned and dried naturally. (3)“SR”填料填縫用黏合劑將槽內、外壁均勻涂刷一遍，外壁要相應涂刷的寬一些，不可漏刷。黏合劑刷好晾1h后，手感快干時，先在槽底沿槽走向放置一條PVC棒。再將“SR”填料均勻切成條狀壓入槽內，并在外壁按設計要求的弧狀堆起2cm高。最后用手捶捶緊，嵌填一定要密實。“SR”填料嵌填完畢后，要及時蓋上“SR”防滲蓋板，再用沖擊鉆鉆孔，安裝電鍍角鋼后埋設10 x75電鍍膨脹螺栓，間距為400mm。利用電鍍角鋼通過電鍍膨脹螺栓將“SR”防滲蓋板嵌固在砼上。 (3) "SR" filler filling adhesive will be in the groove, the outer wall uniform brushing again, the outer wall to the corresponding brushing wider, can not leak brush. After the adhesive brush is dry 1H, when the handle is quick drying, first put a PVC bar at the bottom of the groove along the groove. Then the "SR" uniform filler strips pressed into the groove, and the outer wall of the arc-shaped pile according to the design requirements of 2cm high. Finally, use your hand to punch it tight, and to fill it, it must be dense. After filling the "SR" filler, it is necessary to cover the "SR" impervious cover in time, and then use impact drilling to install the galvanized angle steel, and then bury 10 x75 plating expansion bolt, the distance is 400mm. The "SR" impervious plate is embedded in concrete by electroplating angle steel through electroplating expansion bolt.
|
| 版權聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責。機電之家對此不承擔任何責任。 友情提醒：為規避購買風險，建議您在購買相關產品前務必確認供應商資質及產品質量。 |
